آشنایی با سری روتر 2800

The Cisco 2800 Series comprises four new platforms (refer to Figure 1): the Cisco 2801, the Cisco 2811, the Cisco 2821, and the Cisco 2851. The Cisco 2800 Series provides significant additional value compared to prior generations of Cisco routers at similar price points by offering up to a fivefold performance improvement, up to a tenfold increase in security and voice performance, new embedded service options, and dramatically increased slot performance and density while maintaining support for most of the more than 90 existing modules that are available today for the Cisco 1700, Cisco 2600, and Cisco 3700 Series. The Cisco 2800 Series features the ability to deliver multiple high-quality simultaneous services at wire speed up to multiple T1/E1/xDSL connections. The routers offer embedded encryption acceleration and on the motherboard voice digital-signal-processor (DSP) slots; intrusion prevention system (IPS) and firewall functions; optional integrated call processing and voice mail support; high-density interfaces for a wide range of connectivity requirements; and sufficient performance and slot density for future network expansion requirements and advanced applications. Base Models WAN Interface Cards VWIC-2MFT-E1-DI CISCO2801 WIC-1T VWIC-2MFT-G703 CISCO2811 WIC-2T 2nd Generation VWIC CISCO2821 WIC-2A/S Echo cancellation module CISCO2851 WIC-1B-S/T-V3 Hwics Network Modules WIC-1B-U-V2 HWIC-4ESW Ethernet Switching Network Modules WIC-1DSU-56K4 HWIC-D-9ESW NM-1T3/E3 WIC-1ADSL HWIC-4ESW-POE NM-1HSSI WIC-1ADSL-DG HWIC-D-9-ESW-POE Asynchronous/Synchronous Serial Network Module WIC-1ADSL-I-DG HWIC-1GE-SFP Asynchronous Serial Network Module WIC-1SHDSL – EoS HWIC-4A/S Channelized E1/T1/ISDN-PRI Network Module WIC-1SHDSL-V2 – EoS HWIC-8A/S-RS232 ISDN BRI network module WIC-1SHDSL-V3 HWIC-8A E3 ATM network module WIC-1AM/WIC-2AM HWIC-16A Analog Modem Network Module Extension Voice Module HWIC-4T High-density Voice and Fax Network Module High-density Extension Modules HWIC-AP-G-X High-density Analog Voice and Fax Network Module Voice Interface Cards HWIC-AP-AG-X High-density E1Voice and Fax Network Module VIC-2DID HWIC-1ADSL DSP farm Network Modules VIC-4FXS/DID HWIC-ADSL-B-S/T Content Engine Network Modules VIC2-2FXS HWIC-1ADSLI NM-CIDS-K9 VIC2-2FXO HWIC-ADSLI-B-S/T NM-CUE VIC2-4FXO AIM’s NM-CUE-EC VIC2-2E/M AIM-ATM NM-NAM VIC2-2BRI-NT/TE AIM-COMPR2-V2 NM-AIC-64 VWIC-1MFT-E1 AIM-CUE Circuit Emulation over IP Network Module VWIC-1MFT-G703 AIM-VPN/EPII-PLUS EtherSwitch Service Module VWIC-2MFT-E1 AIM-VPN/EPII-PLUS

CISCO2801 / CISCO2801-AC-IP

Front

1. Slot 0 (VIC or VWIC, for voice only)
2. Slot 1 (WIC, VIC, VWIC, or HWIC)
3. Slot 2 (WIC, VIC, or VWIC)
4. Slot 3 (WIC, VIC, VWIC, or HWIC)
5. Console port
6. Fast Ethernet ports and LEDs
7. System LEDs
8. Auxiliary Power (AUX/PWR) LED
9. Universal serial bus (USB) port
10. AIM/PVDM LEDs
11. Auxiliary port
12. Compact flash (CF) LED
13. External CompactFlash memory card slot
14. Removable center card guides to allow double-wide HWIC-D installation

Rear

1. Input power connector
2. On/Off switch
3. Chassis ground connection
4. –

Product	Description
CISCO2801	2801 Router with an AC Power supply. Includes two integrated FE ports, 4slots(2HWICs), 2 AIM Slots, and IP BASE by default.
CISCO2801-AC-IP	2801 Router with PoE power supply. Includes 2 integrated FE ports, ,4slots (2HWICS), and IP BASE by default.

Return to Top

CISCO2811 / CISCO2811-AC-IP / CISCO2811-DC

 

Front

1. Input power connection (AC Shown, AC-IP or DC is also available)
2. On/Off switch
3. Cisco redundant power supply connector (covered if not used)
4. Console and auxiliary ports
5. Universal serial bus (USB) ports
6. External CompactFlash memory card slot
7. LED indicators

Rear

1. Screw holes for ground lug
2. Fast Ethernet port 0/0
3. Fast Ethernet port 0/1
4. High-speed WAN interface card slot 0
5. High-speed WAN interface card slot 1
6. High-speed WAN interface card slot 2
7. High-speed WAN interface card slot 3
8. Network module enhanced (NME) slot

Product	Description
Cisco2811	2811Router with an AC power supply. Includes 2 integrated FE ports, 4HWIC slots, 2 internal PVDM slots, 1NME slot, 2 AIM slots, and IP BASE by default.
Cisco2811-AC-IP	2811Router with an PoE AC power supply. Includes 2 integrated FE ports, 4HWIC slots, 2 internal PVDM slots, 1NME slot, 2 AIM slots, and IP BASE by default.
Cisco2811-DC	2811Router with an DC power supply. Includes 2 integrated FE ports, 4HWIC slots, 2 internal PVDM slots, 1NME slot, 2 AIM slots, and IP BASE by default.

Return to Top

CISCO2821 / CISCO2821-AC-IP / CISCO2821-DC

 

Front

1. Input power connection (AC-IP power supply shown. AC and DC supplies also available).
2. On/Off switch
3. Console and auxiliary ports
4. Universal serial bus (USB) ports
5. External CompactFlash memory card slot
6. LED indicators
7. Cisco redundant power supply connector (covered if not used)

Rear

1. Gigabit Ethernet port 0/0
2. Gigabit Ethernet port 0/1
3. High-speed WAN interface card slot 0
4. High-speed WAN interface card slot 1
5. High-speed WAN interface card slot 2
6. High-speed WAN interface card slot 3
7. Extension voice module (EVM) slot
8. Network module enhanced (NME) slot1
9. Screw holes for ground lug

Product	Description
Cisco2821	2821 with an AC power supply. Includes 2 integrated Gigabit Ethernet ports, 4 HWIC slots, 3 internal PVDM slots, 1NME-X slot, 1 EVM slot, 2 internal AIM slots, and IP BASE by default.
Cisco2821-AC-IP	2821 with an PoE AC power supply. Includes 2 integrated Gigabit Ethernet ports, 4 HWIC slots, 3 internal PVDM slots, 1NME-X slot, 1 EVM slot, 2 internal AIM slots, and IP BASE by default.
Cisco2821-DC	2821 with an DC power supply. Includes 2 integrated Gigabit Ethernet ports, 4 HWIC slots, 3 internal PVDM slots, 1NME-X slot, 1 EVM slot,2 internal AIM slots, and IP BASE by default.

Return to Top

CISCO2851 / CISCO2851-AC-IP / CISCO2851-DC

 

Front

1. Input power connection (AC-IP power supply shown. AC and DC supplies also available).
2. On/Off switch
3. Console and auxiliary ports
4. Universal serial bus (USB) ports
5. External CompactFlash memory card slot
6. LED indicators
7. Cisco redundant power supply connector (covered if not used)

Rear

1. Gigabit Ethernet port 0/0
2. Gigabit Ethernet port 0/1
3. High-speed WAN interface card slot 0
4. High-speed WAN interface card slot 1
5. High-speed WAN interface card slot 2
6. High-speed WAN interface card slot 3
7. Extension voice module (EVM) slot
8. Network module enhanced (NME) slot1
9. Screw holes for ground lug

Note: The network module slot is compatible with Cisco network modules of type NM (network module), NME (network module enhanced), NME-X (enhanced extended), NMD (double-wide), and NME-XD (enhanced extended double-wide).

Product	Description
Cisco2851	2851 with an AC power supply, 2 Gigabit Ethernet, 4 HWIC slots, 3 internal PVDM slots, 1NME-XD slot, 1 EVM, 2 internal AIM slot , and IP BASE by default.
Cisco2851-AC-IP	2851 with an PoE AC power supply, 2 Gigabit Ethernet, 4 HWIC slots, 3 internal PVDM slots, 1NME-XD slot, 1 EVM, 2 internal AIM slot , and IP BASE by default.
Cisco2851-DC	2851 with an DC power supply, 2 Gigabit Ethernet, 4 HWIC slots, 3 internal PVDM slots, 1NME-XD slot, 1 EVM, 2 internal AIM slot , and IP BASE by default.

Return to Top

Etherswitch Network Modules

NM-16ESW

Product	Description	Features
NM-16ESW	16 port 10/100 EtherSwitch NM	16 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect. QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.
GE-DCARD-ESW	1000BaseT daughtercard for Etherswitch NM
PPWR-DCARD-16ESW	Power daughtercard for 16 port Etherswitch NM

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T	12.2(8)T, 12.3(1)	12.2(8)T1, 12.3(1), 12.3(2)T	12.2(8)T, 12.3(1), 12.3(2)T	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2800 Series (Except 2801) and 3700 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, Enterprise Base, Enterprise Services, SP Services).

 

Return to Top

Etherswitch Network Modules

NM-16ESW-1GIG

Product	Description	Features
NM-16ESW-1GIG	16 port 10/100 EtherSwitch NM with 1 Gigabit Ethernet port	16 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect. Includes gigabit ethernet daughter card. QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.
PPWR-DCARD-16ESW	Power daughtercard for 16 port Etherswitch NM

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T	12.2(8)T, 12.3(1)	12.2(8)T1, 12.3(1), 12.3(2)T	12.2(8)T, 12.3(1), 12.3(2)T	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2800 Series (Except 2801) and 3700 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, yEnterprise Base, Enterprise Services, SP Services).

Return to Top

Etherswitch Network Modules

NM-16ESW-PWR

Product	Description	Features
NM-16ESW	16 port 10/100 EtherSwitch NM	16 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect. Includes Inline power daughter card. QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.
GE-DCARD-ESW	1000BaseT daughtercard for Etherswitch NM

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T	12.2(8)T, 12.3(1)	12.2(8)T1, 12.3(1), 12.3(2)T	12.2(8)T, 12.3(1), 12.3(2)T	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2800 Series (Except 2801) and 3700 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, yEnterprise Base, Enterprise Services, SP Services).

Return to Top

Etherswitch Network Modules

NM-16ESW-PWR-1GIG

Product	Description	Features
NM-16ESW	16 port 10/100 EtherSwitch NM	16 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect. Includes Inline power and Gigabit daughter card. QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T	12.2(8)T, 12.3(1)	12.2(8)T1, 12.3(1), 12.3(2)T	12.2(8)T, 12.3(1), 12.3(2)T	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2800 Series (Except 2801) and 3700 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, yEnterprise Base, Enterprise Services, SP Services).

Return to Top

NMD-36-ESW

Product	Description	Features
NMD-36-ESW	36 port 10/100 EtherSwitch Double-wide NM	36 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect on a double-wide network module (requires chassis with double-wide network module support: 2851, 3660, 3725, 3745, or 3800). QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.
GE-DCARD-ESW	1000BaseT daughtercard for Etherswitch NM
PPWR-DCARD-36ESW	Inline power daughtercard for 36 port EtherSwitch NM

 

Platform Support
Platform	2600	2600XM	2801, 2811,2821	2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	Not supported	Not supported	Not Supported	12.3(8)T	Not supported	Not supported	Not supported	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2851, 3700 Series, and 3800 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, Enterprise Base, Enterprise Services, SP Services).

Return to Top

NMD-36ESW-2GIG

Product	Description	Features
NMD-36ESW-2GIG	36 port 10/100 EtherSwitch Double-wide NM with 2 Gigabit Ethernet ports	36 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect on a double-wide network module (requires chassis with double-wide network module support: 2851, 3660, 3725, 3745, or 3800). Includes two gigabit ethernet ports, 1000Base-T. QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.
PPWR-DCARD-36ESW	Inline power daughtercard for 36 port EtherSwitch NM

 

Platform	2600	2600XM	2801, 2811,2821	2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	Not supported	Not supported	Not Supported	12.3(8)T	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not supported	Not supported	Not supported	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2851, 3700 Series, and 3800 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, Enterprise Base, Enterprise Services, SP Services).

Return to Top

NMD-36ESW-PWR

Product	Description	Features
NMD-36ESW-PWR	36 port 10/100 EtherSwitch Double-wide NM	36 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect on a double-wide network module (requires chassis with double-wide network module support: 2851, 3660, 3725, 3745, or 3800). Includes Inline power daughtercard for 36 port Etherswitch Network Module QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.
GE-DCARD-ESW	1000BaseT daughtercard for Etherswitch NM

 

Platform	2600	2600XM	2801, 2811,2821	2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	Not supported	Not supported	Not Supported	12.3(8)T	Not supported	Not supported	Not supported	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2851, 3700 Series, and 3800 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, Enterprise Base, Enterprise Services, SP Services).

Return to Top

NMD-36ESW-PWR-2GIG

Product	Description	Features
NMD-36ESW-PWR-2GIG	36 port 10/100 EtherSwitch Double-wide NM with 2 Gigabit Ethernet ports	36 Full/Half duplex 10BaseT/100BaseTX Ports with auto detect on a double-wide network module (requires chassis with double-wide network module support: 2851, 3660, 3725, 3745, or 3800). Includes two gigabit ethernet ports, 1000Base-T. QoS and VLAN support from 802.1P and 802.1Q standards. No ISL support. 802.1D Spanning Tree protocols. Optional Additional GE Port(s). Optional In-Line Power.

 

Platform	2600	2600XM	2801, 2811,2821	2851	3620	3631	3640, 3640A	3660, 3725, 3745	3800
IOS Support	Not supported	Not supported	Not Supported	12.3(8)T	Not supported	Not supported	Not supported	12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires an IOS “Plus” image, or a Telco image listed below. In IOS 12.3, EtherSwitch Network Modules are supported in all of the new “Reformation” feature sets for the 2600XM Series, 2851, 3700 Series, and 3800 Series (Advanced Enterprise Services, Advanced IP Services, Advanced Security, IP Base, IP Voice, Enterprise Base, Enterprise Services, SP Services).

Return to Top

1 T3/E3 Network Module

NM-1T3/E3

Product	Description	Features
NM-1T3/E3	Single port T3/E3 Network Module	Supports clear and sub-rate T3/E3. No channelized T3/E3 Supports up to 1 port of T3 or E3 rates. Universal T3/E3 card. Software configures the “card type” to T3 or E3. Card type can be changed later.

 

Platform Support
IOS Support	2600	2650XM, 2651XM	2801	2811,2821,2851	3631, 3620, 3640	2691, 3660, 3725, 3745	3800
NM-1T3/E3	Not supported	12.2(15)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T	Not supported	12.2(15)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

Return to Top

NM-1HSSI

Product	Description	Features
NM-1HSSI	1 HSSI Port Network Module	Similar the PA-H. Uses Cisco Mueselix serial controller Supports speeds up to 45 Mbps

 

Platform Support
IOS Support	2600, 2600XM	2801	2811,2821,2851	3620, 3640	3631	3660	2691, 3725, 3745	3800
NM-1HSSI	Not Supported	Not Supported	12.3(8)T	11.3(5)T, all 12.x	All IOS versions	All IOS versions	All IOS versions	12.3(11)T

Return to Top

Async/Sync Network Modules

NM-4A/S

NM-8A/S

NM-16A/S

Product	Description	Features
NM-4A/S	4 port Async/Sync Network Module	Four, Eight or 16 Async/Sync Ports NM-4A/S and NM-8A/S use Cisco 60-pin “5-in-1” connectors NM-16A/S uses Smart Serial connectors (same as WIC-2T) Max speed 115.2 KBPS async, 128 Kbps sync external clock, 125 Kbps internal clock
NM-8A/S	8 port Async/Sync Network Module
NM-16A/S	16 port Async/Sync Network Module

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620, 3640	3631	3660	2691, 3725, 3745	3800
NM-4A/S	All IOS versions		Not Supported	12.3(8)T	All IOS versions				12.3(11)T
NM-8A/S
NM-16A/S	Not supported	12.2(15)ZJ	Not Supported		Not supported	12.2(15)ZJ	12.2(15)ZJ	Not supported

Return to Top

16 and 32 Port Async Network Modules

 

NM-16A

NM-32A

Product	Description	Features
NM-16A	16 Async Ports	16 or 32 async ports Uses 68-pin connectors with the same cabling and connectors as the 2509 (CAB-OCTAL-xxxx or CAB-25AS-xxxx). Supports 134 kbps async on all ports simultaneously.
NM-32A	32 Async Ports

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620	3640	3631	3660	2691, 3725, 3745	3800
NM-16A	11.3(3)T, 12.0(1), 12.0(1)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.3(1)	12.1(14), 12.2(12), 12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supporte	12.3(8)T	11.2(7)P, 11.3(1), 11.3(1)T, 12.0(1), 12.0(1)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.3(1)	11.2(7)P, 11.3(1), 11.3(1)T, 12.0(1), 12.0(1)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.3(1), 12.3(2)T	12.2(8)T1, 12.3(1), 12.3(2)T	12.0(5)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T
NM-32A

Return to Top

1CE1T1-PRI & 2CE1T1-PRI Network Modules

NM-1CE1T1-PRI

NM-2CE1T1-PRI

Product	Description	Features
NM-1CE1T1-PRI	1-Port Channelized E1/T1/ISDN-PRI Network Module	Balanced or unbalanced E1 termination in the same module. Supports PRI for data, T1-CAS, and E1-CAS R2 signaling. E1 unframed and framed modes (G.703/G.704) available. Cisco IOS® Software configurable for T1 or E1 operation.
NM-2CE1T1-PRI	2-Port Channelized E1/T1/ISDN-PRI Network Module

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620, 3640, 3640A	3631	3660	2691, 3725, 3745	3800
NM-1CE1T1-PRI	Not supported	12.3(1), 12.3(2)T	Not supported	12.3(8)T	Not supported	12.3(1), 12.3(2)T	12.3(1), 12.3(2)T	12.3(1), 12.3(2)T	12.3(11)T
NM-2CE1T1-PRI	Not supported	12.3(1), 12.3(2)T	Not supported	12.3(8)T	Not supported	12.3(1), 12.3(2)T	12.3(1), 12.3(2)T	12.3(1), 12.3(2)T	12.3(11)T

 

Functionality for the NM-1CE1T1-PRI and NM-2CE1T1-PRI modules are supported in all feature sets beginning in Cisco IOS 12.3(1) mainline and 12.3(1)T.

Return to Top

4 and 8 ISDN BRI Network Modules

NM-4B-S/T

NM-8B-S/T

Product	Description
NM-4B-S/T	4-Port ISDN-BRI Network Module
NM-8B-S/T	8-Port ISDN-BRI Network Module

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620, 3640	3631	3660	2691, 3725, 3745	3800
NM-4B-S/T	11.3(4)T, all 12.x	All IOS versions	Not Supported	12.3(8)T	All IOS versions	All IOS versions	12.0(7)XK, 12.1T, 12.2, 12.2T	All IOS versions	12.3(11)T
NM-8B-S/T	11.3(4)T, all 12.x	All IOS versions	Not Supported	12.3(8)T	All IOS versions	All IOS versions	12.0(7)XK, 12.1T, 12.2, 12.2T	All IOS versions	12.3(11)T

Return to Top

ATM E3 Network Modules

NM-1A-E3/NM-1A-T3

Both versions provide a single ATM connection of either 44 Mbps for DS3, or 34 Mbps for E3 using 75-ohm BNC connectors. Both the DS3 and E3 ATM network modules support ATM Forum compliant framing standard AAL5. ATM Traffic Management support includes UBR, UBR+, VBR-rt, VBR-nrt, CBR, and ABR classes of traffic.

 

Product	Description	Features
NM-1A-T3	Single port ATM E3 75 ohm unbalanced	Requires an IOS “Plus” or Service Provider (“-p-“) feature set.
NM-1A-E3	Single port ATM E3 75 ohm unbalanced	Requires an IOS “Plus” or Service Provider (“-p-“) feature set.

 

Platform Support
IOS Support	2600 Series	2691	2811,2821,2851	3620, 3640,3660	3725, 3745	3800
NM-1A-X3	12.1(2)T	12.2(8)T	12.3(8)T	12.1(2)T	12.2(8)T	12.3(11)T

 

Requires an IOS “Plus” or Service Provider (“-p-“) feature set

Return to Top

Analog Modem Network Modules

NM-8AM

NM-16AM

Product	Description	Features
NM-8AM	Network Module with 8 analog modems	Supports speeds up to 33.6 kbps (V.34bis). No 56 kbps support. Two wire leased line is supported beginning in 12.1(5)T with firmware version 1.2.8. Supports fax-out utilizing the Cisco Dial-Out Client. All connectors are RJ-11. Comes with 8 or 16 pink cables (bundle of 8 pink cables is available as CAB-NM-ANALOGMOD).
NM-16AM	Network Module with 16 analog modems
NM-8AM-V2	Network Module with 8 analog modems	8 or 16 internal V.34/V.92/V.90/V.44/V.42bis analog modems per network module Up to 56 Kbps data download and 14.4 Kbps fax communication V.92 Quick Connect and Modem-on-Hold features Centrally managed modem capabilities Simple Network Management Protocol (SMNP) based tools used to manage the rest of the network (such as CiscoView and Cisco Works 2000)
NM-16AM-V2	Network Module with 16 analog modems

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620	3631	3640	3660	2691, 3725, 3745	3800
NM-8AM / NM-16AM	11.3(4)T1, 12.0(1), 12.0(1)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.3(1)	12.1(14), 12.2(12), 12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	11.3(4)T1, 12.0(1), 12.0(1)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.3(1)	Not supported	11.3(4)T1, 12.0(1), 12.0(1)T, 12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.3(1), 12.3(2)T	12.1(1), 12.1(1)T, 12.2(1), 12.2(2)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported
NM-8AM-V2 / NM-16AM-V2	12.3(4)XD	12.3(4)XD	Not Supported	12.3(8)T	Not Supported.	Not Supported.	Not Supported.	12.3(4)XD	12.3(4)XD	12.3(11)T

Return to Top

IP Communications Voice/Fax Network Modules

NM-HD-1V

NM-HD-2V

NM-HD-2VE

Product	Description
NM-HD-1V	1-slot IP communications voice/fax network module. Supports up to four channels of analog/BRI voice using any supported coder-decoder (codec). (No support for T1/E1 or data WAN.)
NM-HD-2V	2-slot IP communications voice/fax network module. Supports up to eight channels of analog/BRI voice using medium complexity codec or six channels using any supported codec. (No support for T1/E1 or data WAN)
NM-HD-2VE	2-slot IP communications enhanced voice/fax network module. Supports analog/BRI/T1/E1 voice and data WAN. Supports up to 48 channels of G.711 codec, 24 channels of medium-complexity codec, or 18 channels of any supported codec. Offers maximum investment protection with support for analog/digital voice and data WAN.

 

IOS Support	2600	2600XM	2691	2801	2811,2821,2851	3620	3631	3640, 3660	3725, 3745	3800
NM-HD-1V	Not Supported	12.2(15)ZJ		Not Supported	12.3(8)T	Not Supported		12.2(15)ZJ	12.2(15)ZJ	12.3(11)T
NM-HD-2V
NM-HD-2VE

 

Note: Requires an IOS “Plus” feature set.

Return to Top

High Density Analog Voice Network Module

NM-HDA-4FXS

Product	Description	Features
NM-HDA-4FXS	High density analog voice/fax network module with 4 FXS. Base Module.	DSPs are on the base board and the DSP expansion module NM-HDA-FXS supports 8 high-complexity or 16 medium-complexity voice channels DSP-HDA-16 supports an additional 8 high-complexity or 16 medium-complexity voice channels You cannot use 2 EM-HDA-8FXS modules on the one card. All other combinations are valid See Config Guide for details of codecs, signalling protocols, configuration and troubleshooting. Requires an IOS Plus Feature set.
EM-HDA-8FXS	8-port voice/fax expansion module – FXS. Expansion module
EM-HDA-4FXO	4-port voice/fax expansion module – FXO. Expansion module
DSP-HDA-16	16-channel DSP module for NM-HDA

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620	3640, 3660	3631	2691, 3725, 3745	3800
NM-HDA	12.2(2)XT, 12.2(8)T	12.2(8)T1	Not Supported	12.3(8)T	Not Supported	12.2(2)XT, 12.2(8)T	Not Supported	All IOS versions	12.3(11)T

 

Requires an IOS “Plus” Feature set.

Return to Top

High Density Voice Network Module

NM-HDV

NM-HDV2

NM-HDV2-1T1/E1

NM-HDV2-2T1/E1

Product	Description	Features
NM-HDV	High Density Voice Network Module (no VWIC, no PVDMs)	Each PVDM-12 contains 3 DSPs Runs up to 12 voice calls using a low complexity CODEC (G.711, G.729a/b, G.726, fax). Runs up to 6 voice calls using a high complexity CODEC (G.729, G.728, G.723.1). PVDM-12 fits into SIMM sockets on the NM-1HDV network module, five PVDM SIMM sockets on the NM-1HDV network module Requires an IOS “Plus” feature set.
NM-HDV-1E1-12	High Density Voice Network Module, with 1 VWIC-1MFT-E1 and 1 PVDM-12
NM-HDV-1E1-30	High Density Voice Network Module, with 1 VWIC-1MFT-E1 and 3 PVDM-12
NM-HDV-1E1-30E	High Density Voice Network Module, with 1 VWIC-1MFT-E1 and 5 PVDM-12
NM-HDV-2E1-60	High Density Voice Network Module, with 1 VWIC-2MFT-E1-DI and 5 PVDM-12
PVDM-12	12-Channel Packet Voice DSP Module
NM-HDV2	IP Communications high-density voice and fax network module.	PVDM2-x, where x equals the number of channels supported using the G.711 codec. x has the following values: 8, 16, 32, 48, 64. Supports the following high complexity codecs: G.723.1, G.728, G.729, G.729b, Global System for Mobile Communications (GSM)-enhanced full rate and Modem Relay. Supports the following medium level codecs: G.711, g.729a, G.729ab, G.726, GSM-Full Rate and Fax Relay. Requires “IP Plus” and higher feature set.
NM-HDV2-1T1/E1	1-port T1/E1 IP Communications high-density voice and fax network module.
NM-HDV2-2T1/E1	2-port T1/E1 IP Communications high-density voice and fax network module.
PVDM2-x	Packet Voice digital signal processor Module. Provides high-density voice connectivity, conferencing, and transcoding capabilities.

IOS Support	2600	2600XM	2801	2811,2821,2851	3620, 3640	3631	3660	2691, 3725, 3745	3800
NM-HDV	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	12.2(8)T1	Not Supported	12.3(8)T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	Not supported	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All IOS versions	12.3(11)T
NM-HDV2	Not Supported	12.3(7)T 12.3(8)T for conferencing or transcoding	Not Supported	12.3(8)T4	Not Supported			12.3(7)T 12.3(8)T for conferencing or transcoding	12.3(8)T4
NM-HDV2-1T1/E1
NM-HDV2-2T1/E1

 

Requires an IOS “Plus” and higher feature set.

Return to Top

IP Communications Voice/Fax Network Modules

NM-HDV-FARM-C36, NM-HDV-FARM-C54, NM-HDV-FARM-C90

Product	Description
NM-HDV-FARM-C36	36-port transcoding and conferencing DSP farm
NM-HDV-FARM-C54	54-port transcoding and conferencing DSP farm
NM-HDV-FARM-C90	90-port transcoding and conferencing DSP farm

 

Platform Support
IOS Support	2650, 2651	2600XM	2691	2801	2811,2821,2851	3640, 3640A, 3661, 3662	3725, 3745	3800
NM-HDV-FARM-C36	12.2(13)T	12.2(13)T		Not Supported	12.3(8)T4	12.2(13)T	12.2(13)T	12.3(11)T
NM-HDV-FARM-C54
NM-HDV-FARM-C90

 

Note: Requires an IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

Content Engine Network Modules

NM-CE-BP-20G-K9 / NM-CE-BP-40G-K9 / NM-CE-BP-80G-K9

NM-CE-BP-SCSI-K9

Product	Description	Features
NM-CE-BP-20G-K9	Content Engine Network Module – Basic Perf – 20GB	CE507 in a network module form factor. Options: 20 GB disk, 40 GB disk, 80 GB disk, or SCSI controller (no disk).
NM-CE-BP-40G-K9	Content Engine Network Module – Basic Perf – 40GB
NM-CE-BP-80G-K9	Content Engine Network Module – Basic Perf – 80GB
NM-CE-BP-SCSI-K9	Content Engine Network Module – Basic Perf – SCSI Adapter
SF-NM-ACNS4.2-K9	Enterprise Caching and ECDN SW v4.2 for NM-CE-BP, 3DES
SF-NM-RCPS-8.0	Combined Real System V8 Proxy and Subscriber for Cisco NM-CE-BP
SF-NM-WMS-1.1	Microsoft Windows Media Server V4 for Cisco NM-CE-BP

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620	3631	3640, 3640A, 3660	2691, 3725, 3745	3800
NM-CE-BP-20G-K9	12.2(13)T, 12.3(1)	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T4	Not supported	Not supported	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T
NM-CE-BP-40G-K9
NM-CE-BP-80G-K9
NM-CE-BP-SCSI-K9

Return to Top

NM-CIDS-K9 Network Module

NM-CIDS-K9

Product	Description	Features
NM-CIDS-K9	Cisco IDS Network Module, 20-GB IDE hard disk	The available configuration is a 20-gigabyte hard disk for logging and storage of events. The external Ethernet port is used for command and control to enable a secure outbound port for management. This setup also allows for both security operations and network operations to have their own command and control interfaces.

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620	3631	3640, 3640A	3660, 2691, 3725, 3745	3800
IOS Support	12.2(15)ZJ or later	12.2(15)ZJ or later	Not Supported	12.3(8)T	Not Supported	Not Supported	Not Supported	12.2(15)ZJ or later	12.3(11)T

Note:Requires IDS feature.

Return to Top

Cisco Unity Express Network Module

NM-CUE

Product	Description	Features
NM-CUE	The Cisco Unity Express network module is fully self-contained with dedicated onboard processing, memory and storage, allowing for efficient message handling, a range of concurrent sessions, simultaneous processing, and ample voice mail storage capacity for a wide range of typical branch office profiles.	Internal Disk Storage: 20 Gig Harddrive. Up to 100 hours of storage. Can be licensed for up to 100 mailboxes.

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620,3631,3640,3640A,3660	2691, 3725, 3745	3800
IOS Support	Not Supported	12.3(4)T	Not Supported	12.3(8)T	Not Supported	12.3(4)T	12.3(11)T

Return to Top

Cisco Unity Express Network Module

NM-CUE-EC

Product	Description	Features
NM-CUE-EC	The Cisco Unity Express network module is fully self-contained with dedicated onboard processing, memory and storage, allowing for efficient message handling, a range of concurrent sessions, simultaneous processing, and ample voice mail storage capacity for a wide range of typical branch office profiles.	supports up to 16 ports of concurrent voice-mail or automated-attendant sessions and up to 250 voice mailboxes (new with Release 2.3).

 

Platform Support
Platform	2691	2600XM	2801	2811,2821,2851	3725,3745	3825, 3845	3800
IOS Support	Yes	Yes	Not Supported	Yes	Yes	Yes	12.3(11)T

 

Mimumum of Release 12.3(11)T5, 12.3(14)T1, 12.4(1) IOS release and Unity Express 2.1

Return to Top

Network Analysis Module

NM-NAM

Product	Description	Features
NM-NAM	The Cisco Branch Routers Series Network Analysis Module is an integrated traffic-monitoring network module that enables network managers to gain application-level visibility into traffic at remote sites to improve network performance, reduce failures, and maximize returns on investments.	WAN Usage Monitoring at the Application Level Application Response Time Monitoring Fault Isolation and Troubleshooting VoIP and QoS Monitoring

 

Platform Support
Platform	2600	2600XM	2801	2811,2821,2851	3620,3631,3640,3640A	3660	2691, 3725, 3745	3800
IOS Support	Not Supported	12.3(4)XD	Not Supported	12.3(8)T	Not Supported	12.3(4)XD	12.3(4)XD	12.3(11)T

 

Note: Only one NAM is supported per router chassis.

Return to Top

Alarm Interface Controller Network Module End Of Sale

NM-AIC-64

Product	Description	Features
NM-AIC-64	Cisco Alarm Interface Controller	Each Network Module can remotely monitor up to 64 network elements, and remotely control up to 16 network devices. Ability to monitor powerplants for voltage fluctuations/thresholds. Environmental condition monitoring for things such as, temperature and humidity. Enhanced premise security monitoring, autonomous control of security camera’s triggered by door/window alarm. Software selectable TL1 or SNMP notification with multiple sessions. More than one AIC can be installed per router for example a Cisco 366x can accommodate up to six AICs and can monitor up to 384 network elements, and remotely control up to 96 network devices. Use the AIC Patch Panel to inject current into loops, and to break out the signals to RJ-21 telco connectors.

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620, 3640	3631	3660	2691, 3725, 3745	3800
NM-AIC-64	12.2(2)XG, 12.2(8)T	12.2(8)T1	Not Supported	12.3(8)T	12.2(2)XG, 12.2(8)T	All IOS versions	12.2(2)XG, 12.2(8)T	Not supported	12.3(11)T

Return to Top

Circuit Emulation Modules

NM-CEM-4SER

NM-CEM-4TE1

Product	Description	Features
NM-CEM-4SER	4 Port Serial Circuit Emulation over IP Network Module
NM-CEM-4TE1	4 Port T1/E1 Circuit Emulation over IP Network Module

 

Platform Support
IOS Support	2600	2600XM	2801	2811,2821,2851	3620, 3640, 3631	3660	2691, 3725, 3745	3800
NM-CEM-4SER	Not Supported	12.3(7)T and later	Not Supported	12.3(8)T	Not Supported	12.3(7)T and later	12.3(7)T and later	12.3(11)T
NM-CEM-4TE1

 

Note: Emulation network modules require one of the following feature sets:

• SP Services and above (Cisco 2600XM Series, and Cisco 2691, 3725, and 3745)
• SP Services
• Advanced IP Services
• Enterprise Services
• Advanced and Enterprise Services
• IP Plus and above (Cisco 3660 only)

Return to Top

Etherswitch Service Module (NME-16ES-1G, NME-16ES-1G-P, NME-X-23ES-1G, NME-X-23ES-1G-1P, NME-XD-24ES-1S-P, NME-XD-48ES-2S-P)

The new Cisco EtherSwitch service modules, greatly expand the capabilities of integrated switching within Cisco routers by providing support for new features such as IEEE 802.3af Power over Ethernet (PoE), local Layer 3 switching, Cisco Network Assistant and Cisco Emergency Responder, and Cisco StackWise™ interfaces (available on NME-XD-24-1S-P only), as well as software feature parity with Cisco Catalyst® 3750 Series switches

Cisco EtherSwitch service modules run their own software, independent of the router’s Cisco IOS® Software image, allowing for easy upgrades and ongoing software feature parity with Cisco Catalyst 3750 Series switches

Product	NME-16ES-1G	NME-16ES-1GP	NME-X-23ES-1G	NME-X-23ES-1G-1P	NME-XD-24ES-1S-P	NME-XD-48ES-2S-P
Cisco pre-standard PoE support and IEEE 802.af PoE	No	Yes*	No	Yes*	Yes*	Yes*
Minimum Cisco IOS Software release for Cisco EtherSwitch service module	12.2(25)SEC	12.2(25)EZ	12.2(25)SEC	12.2(25)EZ	12.2(25)EZ	12.2(25)EZ

 

* When installed in Cisco 3700 Series routers, the modules can only provide Cisco’s pre-standard PoE. The Cisco EtherSwitch service modules do not support any PoE when installed in the Cisco 2691 router.

Platform Support
IOS Support	2691	2800 series	3700 series	3800 series
NME-16ES-1G	12.4(3), 12.4(4)T	2811, 2821, and 2851 Only	12.4(3), 12.4(4)T	12.4(3), 12.4(4)T
NME-16ES-1G-P	12.3(14)T, 12.4(1)	2811, 2821, and 2851 Only 12.3(14)T, 12.4(1)	12.3(14)T, 12.4(1)	12.3(11)T12.3(14)T, 12.4(1)
NME-X-23ES-1G	Not supported	2821 and 2851 Only 12.4(3), 12.4(4)T	Not supported	12.4(3), 12.4(4)T
NME-X-23ES-1G-P	Not supported	2821 and 2851 Only 12.3(14)T, 12.4(1)	Not supported	12.3(14)T, 12.4(1)
NME-XD-24ES-1S-P	Not supported	2851 Only 12.3(14)T, 12.4(1)	Not supported	12.3(14)T, 12.4(1)
NME-XD-48ES-2S-P	Not supported	2851 Only 12.3(14)T, 12.4(1)	Not supported	12.3(14)T, 12.4(1)

 

Requires an IOS Base and above

Return to Top

WIC-1T

One port serial (DB60, Cisco 60-pin “5-in-1” connector ). Supports Max sync speed 2 Mbps. Does not support hot swap.

Platform Support
Feature	Carrier Module	Cisco IOS software support	Sync Max Speed	Async Max Speed	Bisync & Half Duplex
1600	On-Board	All Cisco IOS versions	2.048 Mbps	115.2 Kbps	Cisco IOS Versions 11.2(8)P and later
1700	On-Board	All Cisco IOS versions	2.048 Mbps	115.2 Kbps	All Cisco IOS versions
1800	On-Board	12.3(8)T4	2.048 Mbps	–	–
2600	On-Board, NM-2W	All Cisco IOS versions	2.048 Mbps	Not supported	All Cisco IOS versions
2800	On-Board	12.3(8)T4	2.048 Mbps	–	–
3600	NM-1E2W, NM-1E1R2W, NM-2E2W, NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	All Cisco IOS versions	2.048 Mbps	Not supported	Cisco IOS Versions 11.2(4)XA, 11.3, 11.3T, and all 12.x
3631	On-Board	Cisco IOS versions 12.2(13)T, 12.3(1), 12.3(2)T and higher	2.048 Mbps	Not supported	Cisco IOS versions 12.2(13)T, 12.3(1), 12.3(2)T and higher
2691, 3725, 3745	On-Board, NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T and higher	2.048 Mbps	Not supported	Cisco IOS versions 12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T and higher
3800	On-Board, NM-2W, NM-1FE1R2W, NM-1FE2W, NM-2FE2W, NM-1FE2W-V2, NM-2FE2W-V2	12.3(11)T	2.048 Mbps	–	–

Return to Top

WIC-2T

Provides two serial ports using the “smart serial” connector.

• Asynchronous support with a maximum speed (per port) of 115.2 Kbps, minimum 600 bps. If you need to run at speeds lower than 600 bps, use the AUX port instead.
• Synchronous support with a maximum speed of 2.048 Mbps per port.
  • Supports one port at 8 Mbps when used in NM-1FE1R2W, NM-1FE2W, NM-2FE2W, or NM-2W, or Cisco 2600 chassis WIC slots. All other WIC ports on that network module or Cisco 2600 chassis must not be used.
  • Supports two ports at 4 Mbps each when used in NM-1FE1R2W, NM-1FE2W, NM-2FE2W, or NM-2W, or Cisco 2600 chassis WIC slots. All other WIC ports on that network module or Cisco 2600 chassis must not be used.
  • Supports 8 Mbps on all ports simultaneously on 2691, 3725, and 3745. No restrictions. Maximum six ports at 8 Mbps each.

 

Platform Support
Feature	1600	1700	1800	2600		2600XM		2800	3620, 3640, 3660		3631	2691, 3725, 3745	3800
Carrier Module	Not Required	On-Board	On-Board	On-Board	NM-2W	On-Board	NM-2W	On-Board	NM-1E2W, NM-1E1R2W, and NM-2E2W	NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	On-Board	On-Board, NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	On-Board	NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W
Cisco IOS software support	Not supported	All Cisco IOS versions	12.3(8)T4	All Cisco IOS versions	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T1	12.3(8)T4	Not supported	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	All Cisco IOS versions	All Cisco IOS versions	12.3(11)T	12.3(11)T

 

The Cisco 1600 Series is not capable of supporting the WIC-2T due to lack of Serial Communications Controllers.

The NM-1E2W, NM-1E1R2W, and NM-2E2W Network Modules do not have enough performance power to support the WIC-2T due to hardware limitations.

Return to Top

WIC-2A/S

The WIC-2A/S provides two serial ports using the Smart Serial connector. The only difference between the WIC-2A/S and the WIC-2T is the maximum supported sync speed.

• Aysnchronous support with a maximum speed of 115.2 Kbps, and a minimum of 600 bps. If you need to run at speeds lower than 600 bps, use the AUX port instead.
• Synchronous support with a maximum speed of 128 Kbps.

Platform Support
Feature	1600	1700	1800	2600		2600XM		2800	3620, 3640, 3660		3631	2691, 3725, 3745	3800
Carrier Module	Not Required	On-Board	On-Board	On-Board	NM-2W	On-Board	NM-2W	On-Board	NM-1E2W, NM-1E1R2W, and NM-2E2W	NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	On-Board	On-Board, NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	On-Board	NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W
Cisco IOS software support	Not supported	All Cisco IOS versions	12.3(8)T4	All Cisco IOS versions	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T1	12.3(8)T4	Not supported	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	All Cisco IOS versions	All Cisco IOS versions	12.3(11)T	12.3(11)T

 

The Cisco 1600 Series is not capable of supporting the WIC-2T due to lack of Serial Communications Controllers.

The NM-1E2W, NM-1E1R2W, and NM-2E2W Network Modules do not have enough performance power to support the WIC-2T due to hardware limitations.

Return to Top

WIC-1B-S/T End Of Sale, WIC-1B-S/T-V2, WIC-1B-S/T-V3

One ISDN BRI port (S/T interface, requires external NT-1, RJ-45 connector). Does not support hot swap.

Platform Support
Platform	Cisco 1601(R), 1602 (R), and 1605-R	Cisco 1603, 1603-R, 1604, and 1604-R	Cisco 1720, 1721, 1751, 1760	Cisco 1750	Cisco 1800	Cisco 2600 and 2600XM		Cisco 2800	Cisco 3620 and 3640, 3640A		Cisco 3631	Cisco 3660		Cisco 2691, 3725, and 3745		Cisco 3800
Carrier Module	On-Board	On-Board	On-Board	On-Board	On-Board	On-Board	NM-2W	On-Board	On-Board	NM-2W	On-Board	NM-1E2W, NM-1E1R2W, and NM-2E2W	NM-1FE2W, NM-1FE1R2W, and NM-2FE2W, NM-2W	On-Board	NM-1FE2W, NM-1FE1R2W, NM-2FE2W, and NM-2W	Onboard, NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W
WIC-1B-S/T	All Cisco IOS versions	Not supported	All Cisco IOS versions	All Cisco IOS versions	Not supported	All Cisco IOS versions		Not supported	Cisco IOS versions 11.2(4)XA, 11.2(5)P, 11.3, 11.3T, all 12.x		All Cisco IOS versions	All Cisco IOS versions		All Cisco IOS versions		Not supported
WIC-1B-S/T-V2	Not supported	Not supported	First supported in 12.0(25), 12.1(19), 12.2(16), and 12.3(1)	Not supported	–	First supported in 12.0(25), 12.1(19), 12.2(16), and 12.3(1)		–	First supported in 12.0(25), 12.1(19), 12.2(16), and 12.3(1)		First supported 12.3(1)	First supported in 12.0(25), 12.1(19), 12.2(16), and 12.3(1)		First supported in 12.3(1)		–
WIC-1B-S/T-V3	Not Supported	Not Supported	12.3(10)	Not Supported	12.3(8)T4	12.3(10)		12.3(8)T	Not Supported		Not Supported	12.3(10)		12.3(10)		12.3(11)T

Return to Top

WIC-1B-U-V2

1-port ISDN with NT-1 WIC. Provides a single ISDN BRI connection via an RJ-45 connector.

 

Platform Support
Platform	Cisco 1700	Cisco 1800	Cisco 2600, 2600XM	Cisco 2800	Cisco 3600	Cisco 2691, 3725, and 3745	Cisco 3800
WIC-1B-U-V2	12.1(18), 12.2(13), 12.2(13)T1	12.3(8)T4	12.0(23), 12.1(15), 12.2(10), 12.1(11)T	12.3(8)T	12.0(23), 12.1(15), 12.2(10), 12.1(11)T	12.2(13)T	12.3(11)T

Return to Top

WIC-1DSU-56K4

1-port 4-wire 56/64Kbps DSU/CSU WIC. Provides a single serial connection at speeds up to 64 Kbps.

 

Platform Support
Platform	Cisco 1721	Cisco 1751	Cisco 1760	Cisco 1800	Cisco 2600	Cisco 2600XM	Cisco 2800	Cisco 3620, 3640	Cisco 3660	Cisco 2691, 3725, and 3745	Cisco 3800
WIC-1DSU-56K4	12.2(8)T	12.2(4)T	12.2(11)T	12.3(8)T	11.3(2)XA, 12.1(3)T	12.1(14), 12.2(2), 12.2(8)T1	12.3(8)T4	11.2(4)XA	12.0(5)T	12.2(8)T	12.3(11)T

Return to Top

WIC-1ADSL

One RJ-11 ADSL interface. Supports ADSL over POTS with Annex A ITU 992.1 (G.dmt). Supports up to 23 virtual circuits per WIC. Dying gasp is not supported on WIC-1ADSL, For Dying gasp support please refer to WIC-1ADSL-DG.

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1800	Cisco 2600	Cisco 2600XM	Cisco 2800	Cisco 3600		Cisco 3631	Cisco 2691, 3725, and 3745		3800
Carrier Module	On-Board	On-Board	On-Board	On-Board, NM-2W	On-Board, NM-2W	On-Board	NM-1E1R2W, NM-1E2W, NM-2E2W	NM-1FE1R2W, NM-1FE2W, NM-2FE2W, NM-2W	On-Board	On-Board	NM-1FE1R2W, NM-1FE2W, NM-2FE2W, NM-2W	On-Board	NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W
WIC-1ADSL	Not Supported	12.1(3)XJ, 12.1(3)XP, 12.1(3)XT1, 12.1(5)YB, 12.2(2)T	12.3(8)T4	12.1(5)YB, 12.2(4)T	12.2(8)T1	12.3(8)T4	Not Supported	12.1(5)YB, 12.2(4)T	Not Supported	All Cisco IOS versions	All Cisco IOS versions	12.3(11)T	12.3(11)T

 

Requires an “ADSL” feature set for CISCO 1700 series. Requires a “Plus” feature set for CISCO 2600 / 2600XM / 3600 / 3700 series.

Return to Top

WIC-1ADSL-DG

One RJ-11 ADSL interface. Supports ADSL over POTS with Annex A ITU 992.1 (G.dmt). Supports up to 23 virtual circuits per WIC. Dying Gasp Support.

 

Platform Support
Platform	Cisco 1721, 1751, 1760	Cisco 1800	Cisco 2600XM	Cisco 2800	Cisco 2691, 3725, and 3745		3800
Carrier Module	On-Board	On-Board	On-Board, NM-2W	On-Board	On-Board	NM-1FE1R2W, NM-1FE2W, NM-2FE2W, NM-2W	On-Board	NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W
WIC-1ADSL	12.3(4)T	12.3(8)T4	12.3(4)XD	12.3(8)T4	12.3(4)XD	12.3(4)XD	12.3(11)T	12.3(11)T

 

Requires an “ADSL” feature set for CISCO 1700 series. Requires a “Plus” feature set for CISCO 2600 / 2600XM / 3600 / 3700 series.
The term dying gasp refers to power status as defined in ITU-T standard G.991.2, section 7.1.2.5.3.

Return to Top

WIC-1ADSL-I-DG

Provides a single ADSL over ISDN connection, with Dying Gasp support, at uplink speeds up to 1 Mbps and downlink speeds up to 8 Mbps. This interface card inserts into a Cisco mixed-media network module or directly into a Cisco WIC expansion slot.

 

Platform Support
Platform	Cisco 1721, 1751, 1760	Cisco 1841	Cisco 2610XM-51XM	Cisco 2691	Cisco 2800	3725, 3745	3800
WIC-1ADSL-I-DG	12.3(4)T	12.3(8)T4	12.3(4)XD	12.3(4)XD	12.3(8)T4	12.3(4)XD	12.3(11)T

 

Requires an “ADSL” feature set for CISCO 1700 series. Requires a “Plus” feature set for CISCO 2600 / 2600XM / 3600 / 3700 series.
The term dying gasp refers to power status as defined in ITU-T standard G.991.2, section 7.1.2.5.3.

Return to Top

WIC-1SHDSL End Of Sale

One RJ-11 G.SHDSL interface. Symmetrical WAN speeds (up to 2.3 Mbps) over a single copper pair. Supports up to 23 virtual circuits per WIC.

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1800	Cisco 2600	Cisco 2600XM	Cisco 2800	Cisco 3600	Cisco 3631	Cisco 2691, 3725, and 3745	Cisco 3800
WIC-1SHDSL	Not Supported	12.2(13)T	12.3(8)T4	12.2(4)XL, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(8)T4	12.2(8)T	12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T

 

Requires 1700, 1800, 2600, 2800, 3700, 3800 Chassis WIC Slot, or NM-1FE1R2W, NM-1FE2W, NM-2FE2W, NM-2W WIC slots. Not supported in NM-1E1R2W, NM-1E2W, or NM-2E2W.

Requires an “ADSL” feature set for CISCO 1700 series. Requires a “Plus” feature set for CISCO 2600 / 2600XM / 3600 / 3700 series.

Return to Top

WIC-1SHDSL-V2 End Of Sale

One RJ-11 G.SHDSL interface. Symmetrical WAN speeds up to 2.3Mbps over a single copper pair and up to 4.6Mbps over two copper pairs. Supports up to 23 virtual circuits per WIC.

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1800	Cisco 2691	2610-2651XM	2800	3725, 3745	3800
WIC-1SHDSL-V2	Not Supported	12.3(8)T	12.3(8)T4	12.3(4)XD	12.3(4)XD	12.3(8)T4	12.3(4)XD	12.3(11)T

 

Requires 1700, 1800,2600, 2800, 3800 Chassis WIC Slot, or NM-1FE2W-V2, NM-2FE2W-V2, and NM-FE1R2W-V2.

Return to Top

WIC-1SHDSL-V3

One RJ-11 G.SHDSL interface. Symmetrical WAN speeds up to 2.3Mbps over a single copper pair and up to 4.6Mbps over two copper pairs. Supports up to 23 virtual circuits per WIC.

 

Platform Support
Platform	Cisco 1600	1721,1751,1760	1841	Cisco 2691	2610-2651XM	2811-2851	3725, 3745	2825,3845
WIC-1SHDSL-V3	Not Supported	IP/ADSL IP Base and up	IP Base and up	IP Base and up	IP Base and up	IP Base and up	IP Base and up	IP Base and up

 

* Minimum IOS release 12.4(2)XA and Mimimum IOS T train support 12.4(3rd)T or 12.4(6)T

**Difference between V2 and V3 – Conexant Firmware Version as of 8/20/2005, A29733 (based on 2.3.1)for V2, 3.0.1 for V3

***Requires 1700, 1800,2600, 2800, 3800 Chassis WIC Slot, or NM-1FE2W-V2, NM-2FE2W-V2, and NM-1FE1R2W-V2.

Return to Top

Analogue Modem WICs

WIC-1AM

WIC-2AM

WIC-1AM and WIC-2AM provide V.90 analog modem interfaces for low density applications (router management, dial backup and access). WIC-1AM includes jack for handset sharing access to PSTN line.

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1800	Cisco 2600	Cisco 2600XM	Cisco 2800	Cisco 3600	Cisco 3631	Cisco 2691, 3725, and 3745	Cisco 3800
WIC-1AM	Not Supported	12.2(4)YB	12.3(8)T4	12.2(2)XB, 12.2(8)T	12.2(8)T1	12.3(8)T4	12.2(2)XB, 12.2(8)T	All Cisco IOS versions	All Cisco IOS versions	12.3(11)T
WIC-2AM	Not Supported	12.2(4)YB	12.3(8)T4	12.2(2)XB, 12.2(8)T	12.2(8)T1	12.3(8)T4	12.2(2)XB, 12.2(8)T	All Cisco IOS versions	All Cisco IOS versions	12.3(11)T

 

V.92 is not currently supported.

Return to Top

High-Density Extension Modules

 

EVM-HD-8FXS/DID

Product	Description	Features
EVM-HD-8FXS/DID	High density voice/fax extension module-8 FXS/DID	Cisco high-density extension modules provide an integrated high-density analog/digital voice interface for small or medium branch offices. Together with selected expansion module the Cisco high-density extension module provides a maximum of 24 analog voice ports with 8 ports of DID capability. The Cisco high-density extension module supports up to two expansion modules (EMs) VoIP: H.323, MGCP and SIP VoFR and VoATM (AAL5 and AAL2) Packet voice technologies H.323, MGCP, SIP VoIP, VoFR, VoATM EVM-HD-8FXS/DID is the baseboard Plug in 0, 1 or 2 expansion modules – in any combination EVM-HD uses chassis onboard DSP resources (PVDM2) There is no DSP capability on the EVM module itself
EM-HDA-8FXS	8-port voice/fax expansion module-FXS
EM-4BRI-NT/TE	4-port voice/fax expansion module-BRI (NT and TE)
EM-HDA-6FXO	6-port voice/fax expansion module-FXO
EM-HDA-4FXO	4-port voice/fax expansion module-FXO
EM-HDA-3FXS/4FXO	7-port voice/fax expansion module-3FXS/4FXO

 

Platform Support
IOS Support	2600, 2600XM	2801, 2811	2821, 2851	3620, 3640, 3660	3631	2691, 3725, 3745	3800
EVM-HD-8FXS/DID	Not Supported	Not Supported	12.3(8)T4	Not Supported	Not Supported	Not Supported	12.3(11)T

 

Software Prerequisites: Cisco IOS software with IP Voice feature.

MENTION OF NON-CISCO PRODUCTS OR SERVICES IS FOR INFORMATION PURPOSES ONLY AND CONSTITUTES NEITHER AN ENDORSEMENT NOR A RECOMMENDATION

NOTE:
1. The Cisco High-Density Extension Module operates in the Extension Voice Module (EVM) slot on the Cisco 2821 and Cisco 2851.
2. The High-Density Extension Module operates in any network module or enhanced network module (NME) slot on the Cisco 3825 and Cisco 3845.
3. The Cisco 3825 supports one Cisco High-Density Extension Module, and the Cisco 3845 supports one or two high-density extension modules.
4. The EVM-HD-8FXS/DID Cisco high-density extension module is connected to a distribution frame or patch panel with an RJ-21 cable. RJ-21 cables are not provided with the network module. Cisco does not offer RJ-21 distribution panels and as such customers may, at their sole discretion, consider using a patch panel from Black Box Corporation. The Black Box patch panel accommodates RJ-11 and RJ-45 combinations (Black Box part number: JPM2194A).

Return to Top

VIC-2DID

2-port DID voice/fax interface card. Used to provide off-premises DID connection from central office. Serves only incoming calls from the PSTN. Supports caller ID. Connects to a telco line. Uses RJ-11 connectors.

 

Platform Support
IOS Support	1750, 1751	1841	2600	2600XM	2691	2801	2811,2821,2851	3620,3640,3660	3725, 3745	3800
VIC-2DID	12.2(2)XJ	Not Supported	12.1(5)XM1, 12.2(2)T	12.2(8)T1	12.2(8)T1	12.3(8)T4	12.3(8)T4	12.1(5)XM1	12.2(8)T	12.3(11)T

 

Notes:
1. When used in a Cisco 2600, 3600, or 3700 Series router, requires a voice / fax network module: NM-1V or NM-2V.
2. When used in a Cisco 1751 or Cisco 1760 Series Router, requires a DSP module.
3. Prior to Cisco IOS 12.3 Mainline, requires a Cisco IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

VIC-4FXS/DID

4-port FXS voice/fax interface card. FXS port is used to connect directly to phones, fax machines, and key systems. Generates battery polarity reversal and caller ID.

 

Platform Support
IOS Support	1751	1760	2600XM	2691	2801, 2811,2821,2851	3640,3660	3700	3800
VIC-4FXS/DID	12.3(4)T	12.3(4)T	12.3(4)T	12.3(4)T	12.3(8)T4	12.3(4)T	12.3(4)T	12.3(11)T

 

Notes:
1. When used in a Cisco 2600, 3600, or 3700 Series Router, requires a voice/fax network module: NM-1V or NM-2V
2.Prior to Cisco IOS 12.3 Mainline, requires a Cisco IOS “Plus” features set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

VIC2-2FXS

2-port FXS voice/fax interface card. FXS port is used to connect directly to phones, fax machines, and key systems. Generates battery polarity reversal and caller ID.

 

Platform Support
IOS Support	1751, 1760	2600XM	2691	2801	2811,2821,2851	3631	3640, 3660	3725, 3745	3800
VIC2-2FXS	12.2(15)ZL, 12.3(2)XA, 12.3(2)XC, 12.3(2)XE, 12.3(4)T, 12.3(5)	12.2(15)ZJ, 12.3(4)T	12.2(15)ZJ, 12.3(4)T, 12.3(4)XD	12.3(8)T4	12.3(8)T4	Not Supported. Voice is not supported on 3631.	12.2(15)ZJ, 12.3(4)T	12.2(15)ZJ, 12.3(4)T	12.3(11)T

 

Note:
1. When used in a Cisco 2600, 3600, or 3700 Series Router, requires a voice / fax network module: NM-1V or NM-2V.
2. Prior to Cisco IOS 12.3 Mainline, requires a Cisco IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

VIC2-2FXO

2-port FXO voice/fax interface card [universal card for all countries]. Also supports analog Centralized Automated Message Accounting (CAMA) on any port. FXO port is used to connect to PBX or key system, or to provide off-premises connections to PSTN or PTT. Supports battery reversal detection and caller ID. These Cisco VICs can be software configured to work in all countries. Also used to connect to analog CAMA trunk to provide dedicated E-911 service (North America only)

 

Platform Support
IOS Support	1750, 1751, and 1760	2691	2600XM	2801	2811,2821,2851	3631	3640, 3660	3745, 3725	3800
VIC2-2FXO	12.2(15)ZL, 12.3(2)XA, 12.3(2)XC, 12.3(2)XE, 12.3(4)T, 12.3(5)	12.2(15)ZJ, 12.3(4)T, 12.3(4)XD	12.2(15)ZJ, 12.3(4)T	12.3(8)T4	12.3(8)T4	Not Supported.	12.2(15)ZJ, 12.3(4)T	12.2(15)ZJ, 12.3(4)T	12.3(11)T

 

Notes:
1. When used in a Cisco 2600, 3600, or 3700 Series Router, requires a voice / fax network module: NM-1V or NM-2V.
2.Prior to Cisco IOS 12.3 Mainline, requires a Cisco IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

VIC2-4FXO

4-port FXO voice/fax interface card [universal card for all countries]. Also supports analog CAMA on any port. FXO port is used to connect to PBX or key system, or to provide off-premises connections to PSTN or PTT. Supports battery reversal detection and caller ID. These Cisco VICs can be software configured to work in all countries. Also used to connect to analog CAMA trunk to provide dedicated E-911 service (North America only)

 

Platform Support
IOS Support	1750, 1751, and 1760	2691	2600XM	3640	3620, 3631	3660	3725, 3745	3800
VIC2-4FXO	12.2(15)ZL, 12.3(2)XA, 12.3(2)XC, 12.3(2)XE, 12.3(4)T, 12.3(5)	12.2(15)ZJ, 12.3(4)T, 12.3(4)XD	12.2(15)ZJ, 12.3(4)T	12.2(15)ZJ, 12.3(4)T	Not Supported.	12.2(15)ZJ, 12.3(4)T	12.2(15)ZJ, 12.3(4)T	12.3(11)T

 

Notes:
1. In the Cisco 1751 router, a maximum of one VIC2-4FXO card can be supported.
2. In the Cisco 1760 router, a maximum of two VIC2-4FXO cards can be supported.
3. When used in a Cisco 2600, 3600, or 3700 Series Router, requires a voice / fax network module: NM-1V or NM-2V.
4. Prior to Cisco IOS 12.3 Mainline, requires a Cisco IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

VIC2-2E/M

2-port E&M voice/fax interface card. Used to connect to PBX or key system as tie lines.

 

Platform Support
IOS Support	1751, 1760	1800	2691	2600XM	2800	3620, 3640	3631	3640, 3660	3725, 3745	3800
VIC2-2E/M	12.2(15)ZL, 12.3(2)XA, 12.3(2)XC, 12.3(2)XE, 12.3(4)T, 12.3(5)	Not Supported.	12.2(15)ZJ, 12.3(4)T, 12.3(4)XD	12.2(15)ZJ, 12.3(4)T	12.3(8)T4	11.3(1)T, all 12.x	Not Supported. Voice is not supported on 3631.	12.2(15)ZJ, 12.3(4)T	12.2(15)ZJ, 12.3(4)T	12.3(11)T

 

Voice requires an IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

VIC2-2BRI-NT/TE

This two-port ISDN terminal-side or networkside Basic Rate Interface (BRI) voice interface card connects directly to PSTNs and PBX/PABXs and supports both onpremise and off-premise connections. Supports a total of four voice channels in a single interface card via two RJ-45 physical ports, and enables toll-bypass and voice-overpacket features.

 

Platform Support
IOS Support	1751	1760	2600XM	2691	2800	3640	3660	3700	3800
VIC2-2FXO	12.3(4)T	12.3(4)T	12.3(4)T	12.3(4)T	12.3(8)T4	12.3(4)T	12.3(4)T	12.3(4)T	12.3(11)T

 

Notes:
1. When used in a Cisco 2600, 3600, or 3700 Series Router, requires a voice / fax network module: NM-1V or NM-2V.
2.Prior to Cisco IOS 12.3 Mainline, requires a Cisco IOS “Plus” feature set. 12.3 Mainline and forward supported in “IP Voice” feature set.

Return to Top

1 and 2 Port E1 Multi-Flex Trunk VWIC

Product	Description
VWIC-1MFT-E1	1-Port RJ-48 Multiflex Trunk – E1
VWIC-2MFT-E1	2-Port RJ-48 Multiflex Trunk – E1
VWIC-2MFT-E1-DI	2-Port RJ-48 Multiflex Trunk – E1 With Drop and Insert
VWIC-1MFT-G703	1-Port RJ-48 Multiflex Trunk – E1 for unstructured G.703
VWIC-2MFT-G703	2-Port RJ-48 Multiflex Trunk – E1 for unstructured G.703

 

This Multi-Flex Trunk may be used as a Voice Interface Card or as a WAN Interface Card (in a WIC slot in the 2600 or 3600). Thus it is a Voice WAN Interface Card (VWIC).

 

Platform Support
Feature	1600	1700	1800	2600			2600XM			2800	3600			3631	2691, 3725, 3745			3800
Carrier Module	On-Board	On-Board	On-Board	On-Board	NM-2W	High Density Voice NM	On-Board	NM-2W	High Density Voice NM	On-Board	NM-1E2W, NM-1E1R2W, NM-2E2W	NM-1FE2W, NM-1FE1R2W, NM-2FE2W, NM-2W	High Density Voice NM	On-Board	On-Board	NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W	High Density Voice NM	On-Board	NM-1FE2W, NM-1FE2W-V2, NM-2FE2W, NM-2FE2W-V2, NM-1FE1R2W, NM-2W
VWIC-1MFT-E1	Not supported	12.2(4)YB, 12.2(8)YJ	12.3(8)T4	12.0(5)XK, 12.0(7)T, 12.1, 12.1T, 12.2, 12.2T	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T1	12.2(8)T1	12.3(8)T4	12.0(5)XK, 12.0(7)T, 12.1, 12.1T, 12.2, 12.2T	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T 12.2(13)T3 for V2 NMs		12.3(4)T	12.3(11)T
VWIC-2MFT-E1	Not supported	12.2(4)YB, 12.2(8)YJ	12.3(8)T4	12.0(5)XK, 12.0(7)T, 12.1, 12.1T, 12.2, 12.2T	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T1	12.2(8)T1	12.3(8)T4	Not supported	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T 12.2(13)T3 for V2 NMs		12.3(4)T	12.3(11)T
VWIC-2MFT-E1-DI	Not supported	12.2(4)YB, 12.2(8)YJ	12.3(8)T4	12.0(5)XK, 12.0(7)T, 12.1, 12.1T, 12.2, 12.2T	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T1	12.2(8)T1	12.3(8)T4	12.0(5)XK, 12.0(7)T, 12.1, 12.1T, 12.2, 12.2T	12.0(7)XK, 12.1(1)T, 12.2, 12.2T	12.0(7)XK, 12.1(2)T, 12.2, 12.2T	All Cisco IOS versions	12.2(8)T 12.2(13)T3 for V2 NMs		12.3(4)T	12.3(11)T
VWIC-1MFT-G703	Not supported	12.2(8)YJ	12.3(8)T4	12.1(1)T, 12.2, 12.2T	12.1(1)T, 12.2, 12.2T	Not supported	12.2(8)T1	12.2(8)T1	Not supported	12.3(8)T4	12.1(1)T, 12.2, 12.2T	12.1(1)T, 12.2, 12.2T	Not supported	All Cisco IOS versions	12.2(8)T 12.2(13)T3 for V2 NMs		12.3(4)T	12.3(11)T
VWIC-2MFT-G703	Not supported	12.2(8)YJ	12.3(8)T4	12.1(1)T, 12.2, 12.2T	12.1(1)T, 12.2, 12.2T	Not supported	12.2(8)T1	12.2(8)T1	Not supported	12.3(8)T4	Not supported	12.1(1)T, 12.2, 12.2T	Not supported	All Cisco IOS versions	12.2(8)T 12.2(13)T3 for V2 NMs		12.3(4)T	12.3(11)T

 

For futher reference please refer to http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b6e0f.shtml

Return to Top

2nd Generation 1 and 2 Port T1E1 Multiflex Trunk Voice WAN Interface Cards

Product	Description
VWIC2-1MFT-T1/E1	1-Port T1/E1 Multiflex Trunk Voice/WAN Interface Card
VWIC2-2MFT-T1/E1	2-Port T1/E1 Multiflex Trunk Voice/WAN Interface Card
VWIC2-1MFT-G703	1-Port G.703 Multiflex Trunk Voice/WAN Interface Card
VWIC2-2MFT-G703	2-Port G.703 Multiflex Trunk Voice/WAN Interface Card

 

* Have an onboard slot for a Cisco MFT Dedicated Echo Cancellation (ECAN) Module (part number EC-MFT-32 or EC-MFT-64),

* Support both T1 and E1, providing additional flexibility in configuring the Cisco MFT VWIC2s for supporting T1, fractional T1, E1, and fractional E1 for both voice and WAN applications.

*Include the drop-and-insert multiplexing capability

*enable each port to be clocked from independent clock sources for data applications.

Platform Support
Feature	1721,1751,1760	1841 (data only)	2600XM	2691	3662	3700	2800	3800
VWIC2-XXXX	12.3(14)T	12.3(14)T	12.3(14)T	12.3(14)T	12.3(14)T	12.3(14)T	12.3(14)T	12.3(14)T

 

* Please see the following link for more info about WIC/NM/VIC constraint :

** Data applications require at a minimum the IP Base feature set license and voice applications require at a minimum the IP Voice feature set license.

Return to Top

Multiflex trunk dedicated echo cancellation modules (EC-MFT-32, EC-MFT-64)

Cisco Multiflex Trunk Dedicated Echo Cancellation (MFT ECAN) Modules are dedicated resources for the Cisco Enhanced ITU-T G.168 ECAN feature, providing robust echo cancellation performance for demanding network environments. The modules are daughter cards that attach to Cisco Second-generation Multiflex Trunk Voice/WAN Interface Cards (MFT VWIC2 cards). The dedicated ECAN modules are available in 32- and 64-channel configurations, which match the requirements of the 1- and 2-port T1/E1 MFT VWIC2s, respectively.

 

Platform Support
Platform	1721,1751 and 1760	2600XM	2691	2800	3662	3700	3800
EC-MFC-XX	12.3(14)T, 12.4(1)	12.2(13)T	12.2(13)T	12.3(14)T, 12.4(1)	12.2(13)T	12.3(14)T, 12.4(1)	12.3(14)T, 12.4(1)

 

* Dedicated Echo Cancellation module is not supported on MFT VWIC2 when MFT VWIC2 is used on the Cisco 1751 or 1760.

** It is possible to install a Cisco 32-Channel MFT Dedicated ECAN Module on a 2-port MFT VWIC2. However, not all voice channels will be able to concurrently use the echo cancellation feature.

*** It is possible to install a Cisco 64-Channel MFT Dedicated ECAN Module on a 1-port MFT VWIC2. However, the extra echo cancellation channels will not be used. The only ports on the MFT VWIC2 that can use the module resources are the ports directly attached to the module.

Return to Top

EtherSwitch 4- and 9-Port High-Speed WAN Interface Cards

HWIC-4ESW

HWIC-D-9ESW

Product	Description	Features
HWIC-4ESW	4-port Cisco EtherSwitch 10BASE-T/100BASE-TX autosensing HWIC	4 or 9 10BASE-T/100BASE-TX ports Autosensing, Autonegotiation, and Auto-MDIX Integrated switching 802.1P QoS (Traffic Prioritization) 802.1Q Trunking 802.1D Spanning Tree Protocol Voice VLAN (VLAN) 1
HWIC-4ESW-POE	4-port Cisco EtherSwitch 10BASE-T/100BASE-TX autosensing HWIC with power daughter card
HWIC-D-9ESW	9-port Cisco EtherSwitch 10BASE-T/100BASE-TX autosensing HWIC
HWIC-D-9ESW-POE	9-port Cisco EtherSwitch 10BASE-T/100BASE-TX autosensing HWIC with power daughter card

Note:
1. This part number (HWIC-4ESW-POE / HWIC-D-9ESW-POE) should be ordered only if you require in-line power.
You must also order the matching internal power unit to support in-line power on a Cisco 2800 or Cisco 3800 router.

2. The HWIC-D-9ESW card provides inline power through only 8 of its ports, ports 0 through 7. The ninth port (port 8) is intended to be a stacking port, and as such, does not support inline power.

3. The inline power daughter cards are NOT interchangeable between the 4-port and the (8+1)-port HWICs.

4. There is no option to unstack two HWIC switches. When two HWIC switches are in the same chassis,
they can operate only in stacked mode. If the user configures the switches to operate unstacked, the switches will not operate correctly. All combinations of HWIC switches may be stacked: two HWIC-D-9ESWs, an
HWIC-D-9ESW with an HWIC-4ESW, or two HWIC-4ESWs.

 

Product	Description
PWR-2801-AC-IP=	Cisco 2801 AC inline power supply
PWR-2811-AC-IP=	Cisco 2811 AC inline power supply
PWR-2821-51-AC-IP=	Cisco 2821 and Cisco 2851 AC inline power supply
PWR-3825-AC-IP=	Cisco 3825 AC-IP power supply
PWR-3845-AC-IP=	Cisco 3845 AC-IP power supply

 

Platform Support
IOS Support	1800	2600	2600XM	2800	3620	3631	3640, 3640A, 3660	2691, 3725, 3745	3800
HWIC-4ESW	12.3(8)T4	Not supported	Not supported	12.3(8)T4	Not supported	Not supported	Not supported	Not supported	12.3(11)T
HWIC-4ESW-POE	Not supported
HWIC-D-9ESW	Not supported
HWIC-D-9ESW-POE

Note: The Cisco 2801 can take 2 single-wide (HWIC) or 2 double-wide (HWIC-D) whilst the Cisco 2811, 2821, 2851 can accept 4 single-wide (HWIC) or 2 double-wide (HWIC-D).

Return to Top

Gigabit Ethernet High-Speed WAN Interface Card

 

HWIC-1GE-SFP

Product	Description	Features
HWIC-1GE-SFP	1-port Gigabit Ethernet high-speed WAN interface card	The Cisco Gigabit Ethernet high-speed WAN interface card provides copper and optical Gigabit Ethernet connectivity through a small form-factor pluggable module (SFP), which is inserted into the interface card.

 

Platform Support
IOS Support	1700	1800	2600, 2600XM	2801	2811, 2821, 2851	3620, 3640, 3660	3631	2691, 3725, 3745	3800
HWIC-1GE-SFP	Not Supported	Not Supported	Not Supported	Not Supported	12.3(8)T4	Not Supported	Not Supported	Not Supported	12.3(11)T

 

NOTE:
1. The 2800 can support a maximum of 1 x HWIC-1GE-SFP modules and the 3800 supports a maximum 2 x HWIC-1GE-SFP modules.

2. The HWIC-1GE-SFP requires a SFP that must be purchases separately.

Return to Top

HWIC-4A/S

4-port multiprotocol low speed asynchronous/synchronous HWIC.
Protocols supported are Async (SLIP), Async (PPP), HDLC, Bisync, and transparent.

Interfaces supported are as follows:
– In both DTE and DCE formats: V35, X21, RS-232, and RS-449
– In DTE format only: EIA-530 and EIA-530A

The maximum data rate supported is 256 kbps per port (synchronous).
The maximum data rate supported is 256 kbps per port 230.4 kbps (asynchronous).

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-4A/S	Not supported	Not Supported	12.3(14)T	Not supported	12.3(14)T	Not supported	Not supported	12.3(14)T

Notes:
Connector type is Smart Serial. Available cables can be found here.

Return to Top

HWIC-8A/S-RS232

 

The 8-port RS-232 asynchronous/synchronous HWIC provides 8 asynchronous/synchronous
RS-232 interfaces in both DCE and DTE formats. Data rates of up to 230.4 kbps are supported
in asynchronous mode, and up to 256 kbps in synchronous mode.

The 8-port RS-232 asynchronous/synchronous HWIC uses a quad cable, consisting of a 68-pin
connector on the interface card end and four DB25 connectors on the system end (as pictured).
This cable is available in either DCE or DTE format. The cables include:

 

Cables
Product Number	Cable Type	Length	Connector Type
CAB-HD4-232FC	4-port EIA-232 DCE	10 ft (3m)	Female DB-25
CAB-HD4-232MT	4-port EIA-232 DTE	10 ft (3m)	Male DB-25

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-8A/S-RS232	Not supported	Not Supported	12.3(14)T	Not supported	12.3(14)T	Not supported	Not supported	12.3(14)T

Return to Top

HWIC-8A

The 8-port asynchronous HWIC, provides 8 asynchronous RS-232 interfaces in DTE format, at
data rates of up to 230.4 kbps.

The 8-Port Asynchronous High-Speed WAN Interface Card and 16-Port Asynchronous High-Speed
WAN Interface Card use one (HWIC-8A) or two (HWIC-16A) high-density 8-port connectors. The
8-port asynchronous cable provides the high-density connector on one end and eight RJ-45 plugs
on the other. RJ-45- to DB-25 modular adapters are used to convert the RJ-45 to DB-25 DTE or
DB-25 DCE connections.

 

Cables
Product Number	Cable Type	Length	Connector Type
CAB-HD8-ASYNC	8-port EIA-232	10 ft (3m)	RJ-45
CAB-HD8-KIT	8-port EIA-232 plus eight CAB-25AS-MMOD	10 ft (3m)	Male DB-25
CAB-25AS-MMOD	RJ-45 to DB-25 adapter		Male DB-25
CAB-25AS-FDTE	RJ-45 to DB-25 adapter		Female DB-25

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-8A	Not supported	Not Supported	12.3(14)T	Not supported	12.3(14)T	Not supported	Not supported	12.3(14)T

 

Return to Top

HWIC-16A

The 16-port asynchronous HWIC, provides 16 asynchronous RS-232 interfaces in DTE format,
at data rates of up to 230.4 kbps.

The 16-Port Asynchronous High-Speed WAN Interface Card uses one two high-density 8-port
connectors. The cable provides the high-density connector (68-pin connector) on one end and
eight RJ-45 plugs on the other. RJ-45- to DB-25 modular adapters are used to convert the
RJ-45 to DB-25 DTE or DB-25 DCE connections.

 

Cables
Product Number	Cable Type	Length	Connector Type
CAB-HD8-ASYNC	8-port EIA-232	10 ft (3m)	RJ-45
CAB-HD8-KIT	8-port EIA-232 plus eight CAB-25AS-MMOD	10 ft (3m)	Male DB-25
CAB-25AS-MMOD	RJ-45 to DB-25 adapter		Male DB-25
CAB-25AS-FDTE	RJ-45 to DB-25 adapter		Female DB-25

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-16A	Not supported	Not Supported	Not Supported	Not supported	12.3(14)T	Not supported	Not supported	12.3(14)T

Return to Top

HWIC-4T

The 4-port multiprotocol high speed HWIC. Protocols supported are Async (SLIP), Async (PPP),
HDLC, Bisync, and transparent.

Interfaces supported are as follows:
– In both DTE and DCE formats: V35, X21, RS-232, and RS-449
– In DTE format only: EIA-530 and EIA-530A
– The maximum data rate supported is 8 Mbps per port (synchronous).
– Asynchronous maximum Speed per port is 230.4 kbps.

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-16A	Not supported	Not Supported	Not Supported	Not supported	12.3(14)T	Not supported	Not supported	12.3(14)T

 

Notes:
– The HWIC-4T has Smart Serial interfaces. Suitable cables are listed here.

Return to Top

HWIC-AP-G-X

1. Mounting screws
2. RP-TNC connectors
3. OK LED for the 802.11b/g radio
4. DATA LED for the radio

This access point high-speed WAN interface card (AP HWIC) is a single-wide interface card that houses one radio (single-mode) for connection to a wireless LAN. This interface card operates as an access point when installed in a modular access router with AP HWIC support.

Dual-mode AP carrier card with RP-TNC connectors, dual antennas, and two radios: one 2.4-GHz 802.11b/g
radio and one 5-GHz 802.11a radio. The following are the Cisco part numbers and the geographic regions
for which the interface cards are configured:
– HWIC-AP-G-A—North America
– HWIC-AP-G-E—Europe
– HWIC-AP-G-J—Japan

 

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-AP-AG-x	Not supported	Not Supported	12.4 T	Not supported	12.4 T	Not supported	Not supported	12.4 T

Notes:
– RP-TNC Swivel-mount Omnidirectional Dipole antennas are included with the HWICs.
– Only one AP HWIC is supported in the router at a time. Installation of two AP HWICs in the router is not supported.

Return to Top

HWIC-AP-AG-x

1. Mounting screws
2. RP-TNC connectors
3. OK LED for the 802.11a radio
4. OK LED for the 802.11b/g radio
5. DATA LED for the 802.11a radio
6. DATA LED for the 802.11b/g radio

This access point high-speed WAN interface card (AP HWIC) is a single-wide interface card that houses
two radios (dual-mode) for connection to a wireless LAN. This interface card operates as an access point
when installed in a modular access router with AP HWIC support.

Dual-mode AP carrier card with RP-TNC connectors, dual antennas, and two radios: one 2.4-GHz 802.11b/g
radio and one 5-GHz 802.11a radio. The following are the Cisco part numbers and the geographic regions
for which the interface cards are configured:
– HWIC-AP-AG-A—North America
– HWIC-AP-AG-E—Europe
– HWIC-AP-AG-J—Japan

Platform Support
Platform	Cisco 1600	Cisco 1700	Cisco 1841	Cisco 2600 and 2600XM	Cisco 2800	Cisco 3600	Cisco 3700	Cisco 3800
HWIC-AP-AG-x	Not supported	Not Supported	12.4 T	Not supported	12.4 T	Not supported	Not supported	12.4 T

 

Notes:
– RP-TNC Swivel-mount Omnidirectional Dipole antennas are included with the HWICs.
– Only one AP HWIC is supported in the router at a time. Installation of two AP HWICs in the router is not supported.
– The 4.9-GHz band is not supported.

Return to Top

HWIC-1ADSL ( 1 port ADSL/Pots)

Supports ADSL over basic telephone service with Annex A ITU G. 992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL2+)

Supports Dying Gasp function and has one RJ-11 ADSL interface

 

Platform Support
Platform	Cisco 1841	Cisco 2800	Cisco 3800
HWIC-1ADSL	12.4(4)T Base	12.4(4)T Base	12.4(4)T Base

* ADSL2+ downstream data rates of up to 24 Mbps and upstream data rates of up to 1.5 Mbps

* ADSL2 downstream rates of up to 12 Mbps and upstream data rates of up to 1 Mbps

Return to Top

HWIC-ADSL-B-S/T (2 port ADSL over Pots)

Has one backup ISDN BRI S/T port (data only) and 1 ADSL over Pots port

Supports ADSL over basic telephone service with Annex A ITU G. 992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL2+)

Supports Dying Gasp function and has one RJ-11 ADSL interface

 

Platform Support
Platform	Cisco 1841	Cisco 2800	Cisco 3800
HWIC-ADSL-B-S/T	12.4(6)T Base	12.4(6)T Base	12.4(6)T Base

* ADSL2+ downstream data rates of up to 24 Mbps and upstream data rates of up to 1.5 Mbps

* ADSL2 downstream rates of up to 12 Mbps and upstream data rates of up to 1 Mbps

 

Return to Top

HWIC-1ADSLI ( 1 port ADSL over ISDN)

Supports ADSL over ISDN with Annex B G.992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL2+)

Supports reach-extended ADSL2 standard (G.992.3) Annex L

Supports Dying Gasp function and has one RJ-11 ADSL interface

 

 

Platform Support
Platform	Cisco 1841	Cisco 2800	Cisco 3800
HWIC-1ADSLI	12.4(4)T Base	12.4(4)T Base	12.4(4)T Base

* ADSL2+ downstream data rates of up to 24 Mbps and upstream data rates of up to 1.5 Mbps

* ADSL2 downstream rates of up to 12 Mbps and upstream data rates of up to 1 Mbps

Return to Top

HWIC-ADSLI-B-S/T (2 port ADSL over ISDN)

Has one backup ISDN BRI S/T port (data only) and 1 ADSL over ISDN port

Supports ADSL over ISDN with Annex B G.992.1 (ADSL), G.992.3 (ADSL2), and G.992.5 (ADSL2+)

Supports reach-extended ADSL2 standard (G.992.3) Annex L

Supports Dying Gasp function and has one RJ-11 ADSL interface

 

Platform Support
Platform	Cisco 1841	Cisco 2800	Cisco 3800
HWIC-ADSLI-B-S/T	12.4(6)T Base	12.4(6)T Base	12.4(6)T Base

* ADSL2+ downstream data rates of up to 24 Mbps and upstream data rates of up to 1.5 Mbps

* ADSL2 downstream rates of up to 12 Mbps and upstream data rates of up to 1 Mbps

Return to Top

AIM-ATM, AIM-VOICE-30, AIM-ATM-VOICE-30

Product	Description	Features
AIM-ATM	ATM SAR Advanced Integration Module	AAL1,2, and 5 Support. PVC/SVC support. Up to 30 Voice channels of AAL2 (AIM-ATM requires NM-HDV for voice support) Up to 4 T1/E1 channels of AAL5 (with IMA support). Up to 2048 VCs. IEFT PPP over ATM Support.
AIM-ATM-VOICE-30	SAR and 30 Channel T1/E1 Digital Voice module
AIM-VOICE-30	30 Channel T1/E1 Digital Voice module

 

Platform Support
IOS Support	1800	2600	2600XM	2801	2811, 2821, 2851	3620, 3640	3631	3660	2691, 3725, 3745	3800
AIM-ATM	Not Supported	12.2(2)XA, 12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.3(8)T4	Not Supported	12.3(2)T	12.2(2)XB, 12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.3(11)T
AIM-ATM-VOICE-30	Not Supported	12.2(2)XB, 12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported	Not Supported	12.2(2)XB, 12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported
AIM-VOICE-30	Not Supported	12.2(2)XB, 12.2(8)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported	Not Supported	12.2(2)XB, 12.2(8)T, 12.2(11)YT, 12.3(1), 12.3(2)T	12.2(13)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported

Requires Cisco IOS “Plus” or “SP Services” Feature Sets

 

Return to Top

AIM-COMPR2-V2

 

Product	Description
AIM-COMPR2-V2	The data compressionAIM plugs directly intoone or both of thetwo internal advancedintegration module slotsfor supported Cisco routers.

 

Platform Support
IOS Support	2600XM	2691	2811,2821,2851
AIM-COMPR2-V2	12.2(23), 12.3(6), 12.3(7)T	12.2(23), 12.3(6), 12.3(7)T	12.3(8)T4

Return to Top

AIM-CUE

Product	Description
AIM-CUE	The Cisco Unity Express advanced integration module is fully self-contained with dedicated onboard processing, memory and storage. And, because the advanced integration module is internally installed on the router, it frees external interface slots for other services like analog and digital voice, VPN acceleration or switching. Advanced integration module (AIM-CUE) has a robust onboard microprocessor. Please note the Cisco Unity Express as of version 2.0, now comes with 1GIG of industrial grade compact flash storage.
AIM-CUE-1GBCF	Cisco Unity Express – 1GB Compact Flash
AIM-CUE-512CF	Cisco Unity ExpressCompact – 512MB Compact Flash

 

Platform Support
IOS Support	2600XM	2691	2801,2811,2821,2851	3725, 3745	3825,3845
AIM-CUE	12.3(7)T	12.3(7)T	12.3(8)T4	12.3(7)T	12.3(11)T

Notes:
1. Requires IP Voice feature set.
2. Requires Cisco Unity Express License.

 

Return to Top

Virtual Private Network (VPN) modules

Product	Description	Performance
AIM-VPN/BP	DES/3DES VPN Encryption AIM – Base Performance	2-6Mb/s, 150 tunnels max
AIM-VPN/EP	DES/3DES VPN Encryption AIM – Enhanced Performance	4-14Mb/s, 400 tunnels (2650 performance)
AIM-VPN/HP	DES/3DES VPN Encryption AIM – High Performance	10-24Mb/s, 900 tunnels max
AIM-VPN/BPII	DES/3DES/AES VPN Encryption/Compression Module for 2600XM	20-Mbps 3DES performance in 2611 and up to 22 Mbps on the Cisco 2651XM
AIM-VPN/EPII	DES/3DES VPN Encryption AIM – High Performance	up to 150 Mb/s, 2000 tunnels max
AIM-VPN/HPII	DES/3DES VPN Encryption AIM – High Performance	up to 180 Mb/s, 2000 tunnels max
NM-VPN/MP	DES/3DES VPN Encryption NM for 3620/3640 – Mid Performance	5-12Mb/s, 400 tunnels max
AIM-VPN/BPII-PLUS	DES/3DES/AES Encryption AIM – Base Performance	up to 20-22 Mbps
AIM-VPN/EPII-PLUS	DES/3DES/AES Encryption AIM – Enhanced Performance	up to 80-150 Mbps
AIM-VPN/HPII-PLUS	DES/3DES/AES Encryption AIM – High Performance	up to 180 Mbps

 

Platform Support
IOS Support	1800	2600	2600XM	2800	3620	3631	3640	3660	2691, 3725	3745	3825	3845
AIM-VPN/BP	Not Supported	12.1(3a)XI1, 12.2(1), 12.2(2)T, 12.3(1)	12.2(12), 12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported
AIM-VPN/EP	Not Supported	12.2(2)T, 12.3(1)	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported
AIM-VPN/HP	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	12.1(3a)XI1, 12.2(1), 12.2(2)T, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported
AIM-VPN/BPII	Not Supported	12.1(3a)XI1, 12.2(1), 12.2(2)T, 12.3(1)	12.2(12), 12.2(8)T1, 12.2(11)YT, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported
AIM-VPN/EPII	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	12.2(13)T, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported
AIM-VPN/HPII	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	12.2(13)T, 12.3(1), 12.3(2)T	Not Supported	12.2(13)T, 12.3(1), 12.3(2)T	Not Supported	Not Supported
NM-VPN/MP	Not Supported	Not Supported	Not Supported	Not Supported	12.1(3a)XI1, 12.2(1), 12.2(2)T, 12.3(1)	Not Supported	12.1(3a)XI1, 12.2(1), 12.2(2)T, 12.3(1), 12.3(2)T	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported
AIM-VPN/BPII-PLUS	12.3(8)T	Not Supported	12.3(5c)/12.3(6), 12.3(7)T	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported
AIM-VPN/EPII-PLUS	Not Supported	Not Supported	Not Supported	12.3(8)T	Not Supported	Not Supported	Not Supported	Not Supported	12.3(5c)/12.3(6), 12.3(7)T	Not Supported	12.3(11)T	Not Supported
AIM-VPN/HPII-PLUS	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	Not Supported	12.3(5c)/12.3(6), 12.3(7)T	Not Supported	12.3(5c)/12.3(6), 12.3(7)T	Not Supported	12.3(11)T

Software Prerequisites: Cisco IOS software with the “IPSEC” or “Advanced Security” or higher feature set and maximum ONE Encryption modules/AIMs per Router